Le test comprend 80 questions aléatoires.
Total de questions sur ce sujet : 301
In area A1 the function “Transmission of ship to shore distress alerts” is mainly based on:
The use of SART transponders.
The aerial system of an Inmarsat-C terminal consist of:
An omni-directional aerial.
A tank which contained a category “X” product must undergo a prewash before leaving port in compliance with MARPOL. The resulting residues shall be discharged to a reception facility until the concentration of the substance in the effluent, as indicated by analysis of samples of the effluent taken by the authorized surveyor reaches a certain level. What is that level?
A “Pellistor” is:
It is a sensor that can be used in a combustible gas indicators to detect and measure flammable gas concentration as a percentage of its lower flammable limit.
It is a sensor used in a hydrocarbon measuring instrument that undergoes a chemical change in the presence of a hydrocarbon and air mixture.
You are on a sailing vessel, underway in open water. This vessel is sighted on the starboard bow, on a steady bearing and the distance is closing. By the International Regulations for the Preventing Collisions at Sea, what action will you follow?
By Rule 18, a power-driven vessel underway shall keep out of the way of a sailing vessel. I will maintain my course and speed, but will continue to monitor situation to ensure the other vessel takes avoiding action.
This vessel is clearly a power-driven vessel and I anticipate that the bearing will therefore close and she will pass ahead at a safe distance.
Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I am required to keep out of the way. I will make a broad alteration of course to starboard.
Risk of collision is deemed to exist and, as the other vessel is on a steady bearing on my starboard side, I will maintain my course and speed.
What is the inherent danger in welding/cutting in piping containing freon?
Development of nitrous gases.
Development of explosive gases.
Depletion of oxygen in the air.
Depletion of the ozone layer.
What is most important for crew members when preparing for emergencies?
That people know where to muster.
That people listen to orders given.
That people know where to find designated equipment.
That people are well trained.
IMO MSC.1/Circ 1321 requires that cargo pump rooms on oil tankers shall be mechanically ventilated, using non-sparking suction type fans. What is the minimum number of changes of air per hour that a ventilation system must deliver?
What is the minimum permissible distance measured horizontally between the ship’s shell plating and the outer side bulkhead of the first cargo compartment on a type II chemical tanker?
Not less than moulded breadth / 5.
Not less than moulded breadth / 15.
What immediate action should be taken if a ship unexpectedly runs aground and stops?
Stop engines and tell the engine room to switch over to high suctions.
Stop engines and immediately request “Full Astern”.
Sound the General Alarm and plot the ships position.
A class “D” fire involves what type of material?
Wood or other carbonaceous material.
What will you bring in a lifeboat if the ship is abondoned?
As much biscuit and canned food as possible.
All pets that will most likely not be able to enter the boat by themselves.
Warm clothes, blankets and lifevests.
All valuables like money, jewelry etc.
Which of these conventions is The International Ship and Port Facility Security (ISPS) Code a part of?
The Anti Terrorist International Agreement.
Which statement best describes what happens to the vessel symbol on an ECDIS set in North-up, true motion mode?
Vessel symbol moves across the screen.
Vessel is stopped on the screen, land moves relative.
What is the disadvantage of using chemicals on an oil-spill on the water?
It is difficult to apply the chemicals if the oil drifts away from the ship’s side.
It is difficult to apply chemicals if there is any wind.
The water gets a white colour, which makes it easy to detect the oil-spill.
The chemicals make it difficult to remove the oil from the water.
Master of every ship must provide:
The training during crews working hours only.
Proper rest to the crew after each training programme.
Facilities to conduct training whenever required by the training officer.
A link between the shipboard training officer and the company training officer ashore.
The portable walkie talkies required to be carried by GMDSS regulations should have which channels as a minimum?
The display of the DSC-controller on board is showing the following lines: TX call: Selectiveto: 02114200; Category: RoutineUSB:telephony; DSC Tx 2 189,5 kHz save>send
What are the duties of an effective bridge look out?
All of the alternatives specified.
Keep a lookout for other ships navigation lights and any other dangers which may have no lights.
Ensure there is always a bridge lookout on duty and only leave the lookout when given permission.
Keeping a constant observation around the ship.
When during transmitting the display of a radiotelephone-installation shows a decrease intransmitting power it is:
An indication of aerial problem.
An automatic adjustment of the chosen transmitting mode.
An indication of choosing a wrong channel.
An adjustment of the semi-duplex transmitting power.
The recommended guideline for avoiding the risk of electrostatic potential in a mist produced by using oil and water during Crude Oil Washing operations is that:
Before washing begins, any tank that is to be used as a source of oil for Crude Oil Washing should be partly discharged to remove any water that has settled out during the voyage. The discharge of a layer of at least 1 metres necessary for this purpose.
If a slop tank is to be used to supply oil to drive a Crude Oil Washing operation in a cargo tank, then that slop tank must not have contained slops with a water content of more than 2 %.
As washing begins, any water observed in the stream should be diverted to a slop tank, before Crude Oil Washing of any cargo compartment is commenced.
Crude Oil Washing, where the oil source is stored in a slop tank or other tank that has previously contained slops, should be avoided.
What is the alcohol content in the blood permissible under US legislation before it is defined as intoxication?
Which one of the following items has to be included in an abandon ship drill according to SOLAS regulations?
Checking that life-jackets are correctly donned.
Starting and operating radio life-saving appliances.
Manoeuvring the lifeboat in the water.
Launching and recovery of a survival craft.
What is the correct understanding of the term “Bottlescrew”?
A bottlescrew is the connection ring on the ships deck used to connect lashings and rigging.
A bottlescrew is the threaded screw used to open large bottles.
A bottlescrew is a metal threaded sleeve which adjusts the length and tension on rigging or stays.
A bottlescrew is the special wire rope used to lash containers.
Most minor oilspills are caused by:
Unforeseeable circumstances.
The operating mode of a pyrotechnic signal depends essentially on:
Instructions or diagrams printed on its casing by the manufacturer.
The fact that the user is on board a liferaft, a lifeboat or ship.
The weather conditions of the moment.
A definite standard process.
According to ISGOTT, flue gas that is produced by the burning of a fuel oil that has a high sulphur content will typically contain which of the following amounts of sulphur dioxide?
When a Master takes the leadership in approaching a problem, Must his first action be a decision that will directly solve the problem?
Yes, take full control. Do not delegate to other officers, to avoid mistake.
Not necessary, he shall use all available resources. He should resist the temptation to step in and do it all by himself.
No, he should observ the situation, and let the other senior officers solve the situation.
Yes, with his experience it is most likely that he has the best solution.
The calibration of the ODME is carried with the use of:
The product being carried on that voyage.
Approved bio-degradable light oil.
You are close to the entrance to a port in thick fog. You hear the following signal. What does it mean?
That there is a vessel at anchor in the vicinity. She is more than 100 metres length.
That there is a vessel at anchor in the vicinity. She is less than 100 metres in length.
Onboard training should be organised in such a way that:
Each crew member is trained individually.
It does not contravene with the rest hours of the crew.
It is an integral part of the overall training plan.
An Oil tanker experiences large bending moments and therefore the deck scantlings must be maintained within “x” length amidships, where “x” is:
What do you understand by the term “Risk Assessment”, and how would this be carried out on board?
States than when work has a degree of risk that the work is not carried out.
Requires a great deal of preparation and involves recording everything on paper.
Identify the hazards, quantify the risks, put control measures in place, monitor the work activity and review.
Identify the hazards and specify the personal protective equipment that would be required to complete the work.
Via Inmarsat-C a message is sent to an Inmarsat-C mailbox with a positive delivery notification (PDN). The ground station will:
Send a PDN, if the message has arrived in the mailbox.
Send no PDN’s with messages intended for the mailbox.
Send a PDN, as soon as the message is collected from the mailbox.
Not send any PDN for this message.
You are carrying out a search in a smoke filled compartment wearing a breathing apparatus. At what stage should you start to make your way out of the compartment?
Regularly check your pressure gauge and note how much air you used to reach your work area. Start to return when you have this amount left plus a reasonable reserve.
Wait until the breathing apparatus warning whistle sounds.
Wait for the appropriate signal on your safety line as the personnel outside will be keeping a track of the time you have spent inside.
15 minutes after starting to use the set as this leaves you with 5 minutes air left.
How should you, as helmsman, give feedback to the OOW (officer on watch) that his orders are understood?
You don’t have to give any feedback.
Where would you find the document relating to the “Condition of Freeboard Assignment” onboard?
With the Loadline Certificate.
With the Structural Survey File.
With the Classification Records.
With the Safety Construction Certificate.
The “dew point” of a liquid chemical is often quoted in the documentation relating to its loading and carriage. Which of the following is a definition of “dew point”?
The temperature at which dry-ice melts in Acetone.
The temperature at which a saturated gas exhibits condensation.
The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is seen at the point when air is saturated with moisture.
Measuring the ullage at a cargo tank would mean:
Measuring the distance from the bottom of the tank to the ullage reference point.
Measuring the distance from the surface of the cargo to the ullage reference point.
Measuring the distance from the bottom of the tank to the surface of cargo.
Measuring the distance from the surface of the cargo to the underside of the maindeck.
The emergency fire pump is in accordance with good seamanship and precautionary routines run and tested weekly. Routine checks and maintenance are normally carried out by dedicated personnel. To ensure safe and appropriate operation of the pump, would you consider it beneficial that the same dedicated personnel operate the pump in emergencies?
In case of accidents, it is important that a wide range of personnel must be permitted and trained to operate the pump.
Only senior engineers should operate the emergency pump.
To ensure safe operation of the emergency pump, only dedicated personnel must be permitted to operate the pump.
Is it always possible to use the word “ship” instead of the word “boat”?
A boat can only be used for vessels under 50 metres in length.
Normally a small vessel is called a “boat” rather than a “ship”, otherwise it is not important.
Either can be used anytime.
A large vessel is always called a “ship” and never a “boat”.
… a ship … intended to transport products with appreciably severe environmental and safety hazards which require significant preventative measures to preclude escape of such cargo. Usually the ship is of double-hull construction, with a variety of tank sizes/capacities. What is this the definition of?
A type I chemical tanker as per the IBC Code.
A chemical tanker for the purposes of the 1996 IMO directive MEPC/2.12 circ. on “Mandatory Reporting Requirements for Ships Carrying Dangerous or Polluting Goods”.
A type II chemical tanker, as per the IBC Code.
Oil tankers are subject to cyclical bending moments throughout their life as a result classification society rules require a specific minimum reduction in steel thickness to be maintained within “x” length amidships, where “x” is:
At the entrance to the space where batteries are stored on board the following notice must be fitted:
No entry with naked light and/or flame.
If drugs are discovered onboard your ship:
Write a report a few days after the event and describe everything that occurred.
Disembark crew and passengers as quickly as possible at the next port of call so the authorities can conduct their investigation.
Ensure the witness to the discovery signs your incident report.
Notify the authorities after you arrive at the next port of call.
A “Pellistor” is:
It is a sensor that can be used in a combustible gas indicators to detect and measure flammable gas concentration as a percentage of its lower flammable limit.
It is a sensor used in an oxygen analyser that contains a chemical that are very sensitive to changes in the oxygen content of air.
It is a sensor used in a hydrocarbon measuring instrument that undergoes a chemical change in the resence of a hydrocarbon and air mixture.
Which of the following two digits codes is used to obtain medical advice?
During cargo or bunker operations, oil response equipment is to be:
Used elsewhere in the ship.
A person wearing an anti-exposure suit shall be able to:
Dive into the water to the maximum draft of craft that the ship is provided with.
Don and remove the suit in the water in no more than 5 min if it impairs ability to swim.
Jump from a height equal to that of the stowage of liferafts arranged to be thrown overboard.
Perform all duties associated with abandonment, assist others and operate a rescue boat.
If a DSC distress alert is received on board your ship, what is the first action that should be taken?
Listen for a distress message on the appropriate radio frequency for five minutes.
Nothing, it doesn’t matter.
With reference to oil tanker operations, the terms UFL & LFL stand for:
Upper Flammable Limit and Lower Flammable Limit.
Upper Filling Level and Lower Filling Level.
Upper Flash Point Level and Lower Flash Point Level.
Unidentified Fire Liability and Located Fire Liability.
You are witness to a collision between two other ships close to your vessel. What immediate action should you take?
Send out a distress message on their behalf.
Contact one or both vessels involved in the incident and offer assistance.
Nothing, just standby and wait to see if any assistance is required.
Inform the local coast radio station of the incident and submit your name as a witness.
Wire antenna of 12 metres long is probably:
When handing over the con of a vessel to a pilot, should the Master insist in discussing the passage plan with the pilot while he is there to use his local knowledge and advice on the navigation of the ship?
The passage is well established and known by the pilot, and a plan is therefore not necessary.
A passage plan should be discussed between the Master and pilot, when under pilotage in the same way as discussed with the bridge team when deep sea.
The pilot would probably consider it unnecessary, be more interested in knowing the ship’s characteristics and resist any passage planning discussions with the Master.
What type of search pattern is recommended in the IAMSAR Manual as most effective when the location of the search object is known within relatively close limits?
While navigating using a paper chart marked WGS84 the OOW plots the ships position by four different methods and they all give slightly different positions. Which of the following would be considered the most accurate.
Bearing and distance from a navigation buoy close to the vessel.
Radar ranges from two radar destinctive headlands.
Gyro compass bearings from two lighthouses.
On area A4 the function “Transmission and reception of on scene communications” is mainly based on:
The use of HF DSC and/or Inmarsat-C.
The use of MF and/or VHF R/T.
By a “geographical area call” in the DSC-system is meant:
A DSC-message for all vessels within a certain area marked by a reference position, given in the DSC-message and the degrees are given in southerly and easterly direction.
A DSC-message for all ships heading towards a certain geographical area.
A DSC-message for all vessels within a certain area from a position in the DSC-message, and the degrees are given in northerly and westerly direction.
Prior to discharging cargo from an oil tanker, “line displacement” is usually conducted to:
Verify the pipeline contents with previous grade have been replaced.
The calibration of the ship’s flow meter.
Testing of the automatic shut-down arrangements in the shore line system.
Balancing of a rigid cargo arm.
“Door to door” shipment is covered under:
A Through Bill of Lading.
A Multi-Phase Bill of Lading.
A Destination Bill of Lading.
The correct functioning of a DSC-modem can be checked by means of:
The build-in test facilities in the modem.
The testing-mode of the ever present VHF-DSC-EPIRB.
The obligatory monthly transmission from the RCCs.
The position that is determined by built in GPS-receiver in an Inmarsat-EPIRB has an accuracy of about:
The mandatory color of a hand flare is:
Which personnel must undergo familiarization training on board?
When discussing their chemistry of petroleum cargoes, if “Alkanes” are saturated hydrocarbons, what are unsaturated hydrocarbons?
Which of the following two digits codes is used to obtain maritime assistance?
What is the meaning of this symbol?
How many square metres does the IAMSAR Volume 3 manual suggest may be calmed by releasing 200 litres of lubricating oil slowly through a rubber hose with the outlet maintained just above the surface while the ship proceeds at slow speed?
Approx 5 000 square metres.
Approx 500 square metres.
Approx 50 000 square metres.
Mention some important thoughts for what you have to do when you recognise that fire break out onboard:
Go to the lifeboat start the motor then call the duty officer and commence fight the fire.
Report to bridge or duty officer, actuate the fire alarm, call the persons around the fire and join the fire squad.
Report to bridge or duty officer, actuate the fire alarm, organise and commence fighting the fire.
Commence fighting the fire, call the persons around the fire and join the fire squad.
If the wind speed on a vessel doubles, by approximately how much will the force from it rise?
The force will be Quadrupled.
The force will be Doubled.
The force will be Tripled.
The force will be Quintupled.
What are the three diameters of fire hoses most commonly found on ships?
Ballast introduced into a cargo tank on a chemical tanker which has been washed to such an extent that the ballast contains less than 1 ppm of the substance previously carried may be discharged into the sea without regard to the discharge rate, ship’s speed and discharge outlet location, but under certain conditions. What are those conditions?
That the vessel is not less than 50 miles from the nearest land and is proceeding on route.
Provided the ship is underway and a sample of the ballast water has been drawn from the tank and is stored on board, there are no additional conditions to be imposed on such a discharge.
That the vessel is not less than 12 miles from the nearest land and is in water that is not less than 25 metres deep.
When an inhibitor is added to an oil cargo, the items mentioned on the accompanying certificate include:
Inhibitor name; amount added; date added; period of efficiency; precautions if voyage length exceeds that period; eventual temperature limitation.
Inhibitor class; percentage blended; date added; maximum period of efficiency and applicable temperature limits; maximum storage period on board; contact number of manufacturer.
On a conventional rudder, how much lift force remains if the rudder-angle is decreased to 20 degrees, from an initial 35 degrees?
On the figure there are four (4) possible definitions of the term “BREADTH” given. Which one is the correct one?
Breadth is given by A on the figure.
Breadth is given by B on the figure.
Breadth is given by C on the figure.
Breadth is given by D on the figure.
Inmarsat Telex Service code “31” can be used:
To ask for maritime inquiries.
When the coast-station is disfunctional.
When technical problems are experienced with the Inmarsat terminal.
During the survey of Long Range Identification and Tracking (LRIT) equipment, which document must be available to the surveyor to demonstrate compliance with SOLAS?
A Statement of Installation and Testing by the Approved Service Provider in compliance with SOLAS V/26-4.
A report giving the result of the Performance Test, issued by the manufacturer in compliance with the Flag State Authority requirements.
A report giving the result of the Conformance Test, issued by the Classification Society on behalf of the Flag State Authority.
What is the necessary protection when you are rust chipping with air tools?
Gloves, goggles, earmuffs.
Protective clothing, safety shoes, earmuffs.
Goggles and ear protectors.
Protective clothing, safety shoes, gloves, goggles, earmuffs.
A satellite receives the transmissions of the 406 MHz Cospas-Sarsat EPIRB. The transmissions of the EPIRB will be:
Exclusively passed on to a LUT only between 70° N and 70° S.
Exclusively passed on to a LUT if the satellite sees both the EPIRB and the LUT.
Always passed on to a LUT.
Which word will precede a routine message?
No specific word will precede a routine message.